Carbon Splitters Refurb

Dan · 27-04-2011, 10:28 PM

Quote:

Originally Posted by karbonkid

Afraid not no, never dealt with them before.

For peps in Reading area theres a good chap, Noel @ NUR-Motorsport . He manufactures carbon parts/ Repairs.

Any experience of this guy Alex? I caught my front bumper on a flower pot up the Mrs drive this morning

it will polish out but not happy about it and both the bumper and splitter are chipped to fook anyways! Oh, and I caught the offside splitter on the leading edge a while back as well!

NZ_M3 · 28-04-2011, 10:06 AM

Superb work on the bumper Alex ... time to open your own repair shop me thinks

karbonkid · 28-04-2011, 11:01 AM

Quote:

Originally Posted by NZ_M3

Superb work on the bumper Alex ... time to open your own repair shop me thinks

Back off! Me not doing another fooker!!

Ta thou, I was well impressed with the results from just a series of aerosols. So much so I rewound time so I could take pics of prep stages so you lot can ave a go.

M5 Powered · 28-04-2011, 09:25 PM

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow.

s.mac · 28-04-2011, 09:31 PM

Alex, bumper looks mint ! i like to do a bit of diy but that is going some

billyboysm3 · 12-08-2011, 01:29 PM

Quote:

Originally Posted by M5 Powered

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow.

M5 Powered, after putting some miles on the splitters since the refurb how are the holding up?

Shimmy same to you?

Probably get mine done in the next couple of months.

M5 Powered · 13-08-2011, 07:04 PM

Still as new!

**shimmy** · 14-09-2011, 05:32 PM

Quote:

Originally Posted by billyboysm3

M5 Powered, after putting some miles on the splitters since the refurb how are the holding up?

Shimmy same to you?

Probably get mine done in the next couple of months.

Did mine at Finishline........won't do again! Peeling

billyboysm3 · 14-09-2011, 02:24 PM

Quote:

Originally Posted by M5 Powered

Finally got round to picking up my splitters which were refurbed by Perkins.

The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow.

M5 Powered have you got any picts?

sailorbaz · 08-05-2011, 08:31 AM

Alex, you said you used Rattle cans, where did you get them? Online or local? A local Motor factor can get our SG made up in Aerosols but I'm concerned as to the match. I also found some on Ebay, WA08 is it? Comes in two cans, £20 for the paint and the lacquer.

Thanks in advance, Baz

28-04-2011, 09:25 PM	#4
M5 Powered S5 - Full Throttle Join Date: May 2009 Location: Solihull, West Midlands Posts: 297 Casino cash: $2712	Finally got round to picking up my splitters which were refurbed by Perkins. The result? For 85 quid they look new. I can't even see where the stone chips were! Pics to follow. __________________ M3 CSL, Silver Grey, 2004, Factory de-limit, Alcon BBK, Rogue Rear Control Arms, Turner Top Mounts, Braille CF Battery

13-08-2011, 07:04 PM	#7
M5 Powered S5 - Full Throttle Join Date: May 2009 Location: Solihull, West Midlands Posts: 297 Casino cash: $2712	Still as new! __________________ M3 CSL, Silver Grey, 2004, Factory de-limit, Alcon BBK, Rogue Rear Control Arms, Turner Top Mounts, Braille CF Battery

28-04-2011, 10:06 AM	#2
NZ_M3 S5, Sport On, DSC M-track Join Date: Jun 2008 Location: Auckland, New Zealand Posts: 1,434 Casino cash: $13579	Superb work on the bumper Alex ... time to open your own repair shop me thinks

28-04-2011, 09:31 PM	#5
s.mac CSL Register Uber-poster! Join Date: Jun 2008 Posts: 4,247 Casino cash: $15600	Alex, bumper looks mint ! i like to do a bit of diy but that is going some