CSL Register

Go Back   CSL Register > Other M-Cars > General M-Car Discussion

Reply
 
Thread Tools Display Modes
Old 10-10-2013, 03:48 PM   #1
oilman
S5 - Full Throttle
 
oilman's Avatar
 

Join Date: Jul 2008
Location: cornwall
Posts: 363
Casino cash: $2021
oilman
Default Engine Oil Viscosity

Engine Oil Viscosity

Viscosity is the most misunderstood aspect of oil and yet it is the most important.

Viscosity is the force required to shear (break) the oil at a certain speed and temperature. Oils work because they have viscosity; the drag of a rotating part pulls oil from a low-pressure area into a high pressure area and “floats” the surfaces apart. This is called “hydrodynamic lubrication” and crankbearings depend on it.

Oil must be capable of flowing at low temperatures, so that it gets around the engine in a fraction of a second at start-up and must protect engine components at high temperatures without evaporating or carbonising and maintain adequate (not excessive) oil pressure. Many people think that the thicker the oil, the better the protection, but if the oil is too thick, it will not flow properly, leading to reduced protection.

The numbers on every can of oil indicate its performance characteristics when new but there are many misconceptions on what these numbers actually mean.

For multigrade oils you will see two numbers (for monograde oils only one). The first is followed by a “w” and is commonly 0, 5, 10, 15 or 20. The second number is always higher than the first and is commonly 20, 30, 40, 50 or 60. The first and second numbers ARE NOT related.

The “w” number (0, 5, 10, 15 or 20)
When multigrade oils first appeared, a low temperature test called “w” (meaning “winter” not weight) was introduced. Using a “Cold Crank Simulator", the test measures the oils ability to flow at low temperatures. ALL oils are THICKER at low temperatures than at high temperatures but the lower the “w” number, the quicker the oil will flow at low temperatures.

The second number (20, 30, 40, 50 or 60)
This number is known as the SAE (Society of Automotive Engineers) number and is measured in “Centistokes” (cst) at 100C. Centistokes (cst) is the measure of a fluid's resistance to flow (viscosity). It is calculated in terms of the time required for a standard quantity of fluid at a certain temperature to flow through a standard orifice. The higher the value, the thicker the oil.

An oils cst at 100C determines its SAE rating within the following parameters.
SAE 20 = 5.6 to less than 9.3cst
SAE 30 = 9.3 to less than 12.5cst
SAE 40 = 12.5 to less than 16.3cst
SAE 50 = 16.3 to less than 21.9cst
SAE 60 = 21.9 to less than 26.0cst

ALL oils labelled 40 must fall within the SAE parameters at 100C so everything from a monograde 40 to multigrade 0w-40, 5w-40, 10w-40, 15w-40 or 20w-40 are approximately the same thickness at 100C.

Some oil companies label oils as SAE 35, 45 or 55, but as you can see from the above figures, there isn't a SAE 35, 45 or 55. This "could" be because they are approximately on the boundary of the two grades, but as we don't deal with any of those I can't really comment further.

Summary

Cold start.
A 5w-40 will flow better than a 10w-40.
A 10w-50 will flow better than a 15w-50
A 5w-40 is the same as a 5w-30

At operating temperatures.
A 10w-50 is thicker than a 10w-40.
A 15w-50 is thicker than a 5w-40
A 0w-40 is the same as a 10w-40

If you look above, you will see that the figures quoted do not indicate at all as to whether the oil is synthetic or mineral based... Well except for 0w oils as synthetic PAO basestock is required to acheive this viscosity.

Generally the oil you use should be based on the manufacturers recommendation found in the owners manual, but then modifications, climate and the type of use can affect that recommendation. If you are unsure of what is the correct recommendation for your car and would like to know more please contact us here oilman@opieoils.co.uk

With thanks to John Rowland of Fuchs/Silkolene

Cheers

Tim and the Opie Oils team
__________________
Use the code CSLR and get 10% Club Discount
oilman's website: http://www.opieoils.co.uk/ - register for news and offers
email: sales@opieoils.co.uk
phone: 01209 202944
oilman is offline   Reply With Quote
Old 12-10-2013, 07:53 AM   #2
Straightsix
S5 - Full Throttle
 
Straightsix's Avatar
 

Join Date: Sep 2011
Posts: 357
Casino cash: $1823
Straightsix is on a distinguished road
Default

Great info thank you :-)
Straightsix is offline   Reply With Quote
Old 12-10-2013, 08:09 AM   #3
Straightsix
S5 - Full Throttle
 
Straightsix's Avatar
 

Join Date: Sep 2011
Posts: 357
Casino cash: $1823
Straightsix is on a distinguished road
Default

How do manufacturers such as BMW choose which specification of oil to use for their engines. For example the BMW E46 M3 is recommended to use Castrol TWS 10W-60.

Seems mid-range for cold starting in being able to flow nicely being bang in the middle between 0, 5, 10, 15, 20. But the 60 indicates very thick specification for 10W. Presumably to help protect, lubricate, cool for cold starts and the high revving nature of the engine at around 8000rpm etc ?
Straightsix is offline   Reply With Quote
Old 14-10-2013, 09:57 AM   #4
oilman
S5 - Full Throttle
 
oilman's Avatar
 

Join Date: Jul 2008
Location: cornwall
Posts: 363
Casino cash: $2021
oilman
Default

Hi

The E46 M3 (and E39 M5) were originally intended to use a BMW LL98 spec oil, so 0w-30, 5w-30, 0w-40 or 5w-40, but they were found to use massive amounts of oil if one of those grades was used. They were fine in protection terms, but the consumption was often around 350 miles per litre, so after the M5 was released, they changed the spec to 10w-60 to prevent that.

The original oil spec of an engine is based on tolerances, engine temperature in testing and previous experience, but when the car goes on the market, things can show up, like excessive consumption or in certain cases, engine failure, and then they need to look at the oil to see if it's correct.

Cheers

Tim
__________________
Use the code CSLR and get 10% Club Discount
oilman's website: http://www.opieoils.co.uk/ - register for news and offers
email: sales@opieoils.co.uk
phone: 01209 202944
oilman is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +1. The time now is 10:36 AM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c)www.wickedwifi.co.uk