Harness mountings (again)

rstoughy · 06-03-2012, 11:02 PM

I know its been done to death but for those who dont run a cage where and how do you have your harnesses mounted?

Lawsy, Shimmy what did / do you guys do???

Cheers

**CraigMillwardCroft** · 09-03-2012, 03:09 PM

Have put the rear eyes in place where the baby seat anchors go, still trying to decide where to put the side eyes, but do have the plates for them

rstoughy · 09-03-2012, 03:45 PM

Craig,
Is that the ISOFIX locations you have used?
I was told to avoid these as they are not designed to brace an adult, only a child???

I will likely go rear cage or rear brace at some point but just looking for something in the interim.

**CraigMillwardCroft** · 09-03-2012, 03:52 PM

It is the ISOFIX place but remove the bracket and put in the eyes from the full harness as long as they are M10 thread.

rstoughy · 09-03-2012, 04:29 PM

Quote:

Originally Posted by CraigMillwardCroft

It is the ISOFIX place but remove the bracket and put in the eyes from the full harness as long as they are M10 thread.

karbonkid · 09-03-2012, 04:49 PM

What you trying to achieve Paul? Existing seats with non permanent harnesses? or bolted in and rear seats out of action?

**shimmy** · 09-03-2012, 04:57 PM

i have eyebolts in rear isofix, side seatbelt bolt and new one drilled and pkated into driveshaft tunnel

i always put on the seatbelt so no worries either way

Yanto · 09-03-2012, 07:35 PM

4x2 across the bedroom ceiling, two mounting points 1m apart allowing swing space...

Sorry, wrong thread.....

rstoughy · 09-03-2012, 10:13 PM

Quote:

Originally Posted by karbonkid

What you trying to achieve Paul? Existing seats with non permanent harnesses? or bolted in and rear seats out of action?

Bolted in with a fixed bucket. Rear seats will likely stay in place though excluding MOT time as the drivers seat only slides and doesnt tilt now.

Quote:

Originally Posted by Yanto

4x2 across the bedroom ceiling, two mounting points 1m apart allowing swing space...

Sorry, wrong thread.....

karbonkid · 11-03-2012, 08:28 PM

Quote:

Originally Posted by rstoughy

Bolted in with a fixed bucket. Rear seats will likely stay in place though excluding MOT time as the drivers seat only slides and doesnt tilt now.

If seats are fixed then rear seats are useless. Best solution is a cage by the sounds of your use. Unless you get a rear strut/ harness bar. Then you tuck harnesses away into boot, fold up seats and have that OEM look without committing to a semi/ permanent cage.

Mounting points circled below for eye bolt/ belt buckle fitting.

06-03-2012, 11:02 PM	#1
rstoughy S6, Sport On, Traction Off Join Date: Jun 2008 Location: Aberdeenshire Posts: 1,947 Casino cash: $25387	Harness mountings (again) I know its been done to death but for those who dont run a cage where and how do you have your harnesses mounted? Lawsy, Shimmy what did / do you guys do??? Cheers __________________ Paul. Ooooft!!! 15yrs in the CSL and still loving it "shine on you crazy diamond"

09-03-2012, 03:45 PM	#3
rstoughy S6, Sport On, Traction Off Join Date: Jun 2008 Location: Aberdeenshire Posts: 1,947 Casino cash: $25387	Craig, Is that the ISOFIX locations you have used? I was told to avoid these as they are not designed to brace an adult, only a child??? I will likely go rear cage or rear brace at some point but just looking for something in the interim. __________________ Paul. Ooooft!!! 15yrs in the CSL and still loving it "shine on you crazy diamond"

09-03-2012, 04:49 PM	#6
karbonkid S6, Sport On, Traction Off Join Date: Nov 2008 Location: Sussex Posts: 1,912 Casino cash: $10231	What you trying to achieve Paul? Existing seats with non permanent harnesses? or bolted in and rear seats out of action? __________________

09-03-2012, 04:57 PM	#7
shimmy CSL Register Uber-poster! Join Date: Apr 2008 Location: Uk Posts: 14,646 Casino cash: $43909	i have eyebolts in rear isofix, side seatbelt bolt and new one drilled and pkated into driveshaft tunnel i always put on the seatbelt so no worries either way __________________ .

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-03-2012, 03:09 PM	#2
CraigMillwardCroft CSL Register Uber-poster! Join Date: Oct 2010 Location: Marlow Posts: 3,973 Casino cash: $18153	Have put the rear eyes in place where the baby seat anchors go, still trying to decide where to put the side eyes, but do have the plates for them

09-03-2012, 03:52 PM	#4
CraigMillwardCroft CSL Register Uber-poster! Join Date: Oct 2010 Location: Marlow Posts: 3,973 Casino cash: $18153	It is the ISOFIX place but remove the bracket and put in the eyes from the full harness as long as they are M10 thread.

09-03-2012, 07:35 PM	#8
Yanto CSL Register Uber-poster! Moon Lander Champion! Ragdoll Master Champion! Join Date: Mar 2009 Location: Docklands, London Posts: 5,931 Casino cash: $40036	4x2 across the bedroom ceiling, two mounting points 1m apart allowing swing space... Sorry, wrong thread.....