Help / Advice please, DSC & ABS Failed? - Page 2

Bounce · 26-09-2011, 10:43 PM

You get those lights if you dont post for 2 months.

_Nathan_ · 26-09-2011, 11:13 PM

I had similar for a failed steering angle sensor from memory but don't have a documented photo history of every warning light ever so might be wrong...

Get a GT1 on it and all will be revealed.

shane@mbtech · 27-09-2011, 12:03 AM

Quote:

Originally Posted by _Nathan_

I had similar for a failed steering angle sensor from memory but don't have a documented photo history of every warning light ever so might be wrong...

Get a GT1 on it and all will be revealed.

Yep seen that before with these lights, BMW wanted to replace the steering angle sensor, but we just reset it and it has been fine since.

Dan · 27-09-2011, 12:20 AM

Quote:

Originally Posted by lawsy

I still reckon possible brake fluid low.

Also open bonnet and check switch. Then slam it shut.

I was thinking about bonnet problem too, is there a specific switch to check mate?

NZ_M3 · 27-09-2011, 04:03 AM

DSC Pressure sensor (one of the two on the brake master cylinder).

Basically measures brake pressure - most likely the one closer to the firewall that's failed (the bitch one to take out).

If you plug it in the GT1 one sensor will show pressure whilst the other show 0psi

manos///3 · 27-09-2011, 09:07 AM

I had the same problem before 4 months. Same lights on the dash.
Gt1 didn't recognize any fault. Just reset them and everything is ok since then!

Dan · 27-09-2011, 01:55 PM

Quote:

Originally Posted by NZ_M3

DSC Pressure sensor (one of the two on the brake master cylinder).

Basically measures brake pressure - most likely the one closer to the firewall that's failed (the bitch one to take out).

If you plug it in the GT1 one sensor will show pressure whilst the other show 0psi

Thanks Tom, it'll more than likely be a warranty job if anything gets replaced so should save me the hassle.

Quote:

Originally Posted by manos///3

I had the same problem before 4 months. Same lights on the dash.
Gt1 didn't recognize any fault. Just reset them and everything is ok since then!

How did you reset it Manos, using the GT1 I assume?

manos///3 · 27-09-2011, 05:42 PM

Quote:

Originally Posted by Dan

How did you reset it Manos, using the GT1 I assume?

Gt1 off course!

26-09-2011, 11:13 PM	#12
_Nathan_ Driving it like I nicked it Join Date: Sep 2008 Posts: 2,099 Casino cash: $13060	I had similar for a failed steering angle sensor from memory but don't have a documented photo history of every warning light ever so might be wrong... Get a GT1 on it and all will be revealed. __________________ Nathan

26-09-2011, 10:43 PM	#11
Bounce CSL Register Uber-poster! Join Date: Nov 2009 Location: Cornwall Posts: 7,057 Casino cash: $35793	You get those lights if you dont post for 2 months.

27-09-2011, 04:03 AM	#15
NZ_M3 S5, Sport On, DSC M-track Join Date: Jun 2008 Location: Auckland, New Zealand Posts: 1,434 Casino cash: $13579	DSC Pressure sensor (one of the two on the brake master cylinder). Basically measures brake pressure - most likely the one closer to the firewall that's failed (the bitch one to take out). If you plug it in the GT1 one sensor will show pressure whilst the other show 0psi

27-09-2011, 09:07 AM	#16
manos///3 S2 - Picking it up Join Date: May 2011 Location: Greece Posts: 42 Casino cash: $828	I had the same problem before 4 months. Same lights on the dash. Gt1 didn't recognize any fault. Just reset them and everything is ok since then!