Limiter Kit - Rogue Engineering OR Turner??

cslbecks · 28-10-2008, 05:12 PM

Im getting the RTAB Limiter Kit fitted and ive heard that Rogue Engineering also provide the same/similar kit as the Turner one.
Are these really both the same/do the same job - or is one better than the other??
I believe that CA supply the Rogue one and Simpsons supply the Turner one.
Any views or advice greatly appreciated.

Bravo73 · 28-10-2008, 06:10 PM

If you're getting the work done at Simpsons, I suggest that you go with the Turner's version. Simpsons obviously choose to stock the Turner one for a reason.

Are you getting the bushes themselves changed at the same time?

cslbecks · 28-10-2008, 07:08 PM

I dont think my bushes will need changing - the cars only done 16k - but will get them to check them and if they need doing i will get them replaced also.
I just wondered if anyone had had the Rogue Limiter kit fitted??

Bravo73 · 28-10-2008, 07:13 PM

If you're going to the hassle and cost of having the limiting kit fitted, you'd be daft to not change the bushes at the same time. IIRC, the bushes themselves cost around £15 and the additional labour shouldn't be that much.

I would even go as far to say that Simpsons will advise you to fit new bushes anyway. They certainly did when I bought the limiting kit off them recently.

cslbecks · 28-10-2008, 07:41 PM

Yes - i wont scrimp if they need doing - but dont really see the point if they are ok?? Its not the cost of the bushes, its the extra labour - but as i said i wont scrimp if they need doing - knowing me i will most likely get them done anyway so i know everythings fresh etc. Thanks as always Bravo for your help and advice.

**glendog74** · 28-10-2008, 08:25 PM

Quote:

Originally Posted by cslbecks

Its not the cost of the bushes, its the extra labour

It's literally a 5 minute job to swap them out/in as they will have already disconnected the rear trailing arm anyway to do the limiter kit. Minimal extra labour...

cslbecks · 28-10-2008, 10:50 PM

ok - cool - will most likely get them done then regardless!

**shimmy** · 29-10-2008, 01:19 AM

Quote:

Originally Posted by cslbecks

ok - cool - will most likely get them done then regardless!

only sensible answer tbh

the bushes could fail the day you drive out as very hard to pick up the start of the fault

mine went at 18k miles

pkumarm3 · 02-01-2009, 07:29 PM

Powerflex RTABs are the best you can buy

they are poly-urethane. they are stiff, but also have some play so you won't be killing yourself when your car creaks non stop (like it would with the Rogue RTABs)

englebert · 02-01-2009, 09:19 PM

My car had covered well under 16k and had busted bushes and a broken rear spring!

28-10-2008, 05:12 PM	#1
cslbecks S4 - Getting the hang of it Join Date: Oct 2008 Location: London, Essex Posts: 178 Casino cash: $250	Limiter Kit - Rogue Engineering OR Turner?? Im getting the RTAB Limiter Kit fitted and ive heard that Rogue Engineering also provide the same/similar kit as the Turner one. Are these really both the same/do the same job - or is one better than the other?? I believe that CA supply the Rogue one and Simpsons supply the Turner one. Any views or advice greatly appreciated.

02-01-2009, 09:19 PM	#10
englebert S5 - Full Throttle Join Date: Jun 2008 Location: Kent Posts: 397 Casino cash: $705	My car had covered well under 16k and had busted bushes and a broken rear spring! __________________ '03 SG CSL - SOLD Making do with a CSL replica, 1M and E90 M3.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
E46 M3 CSL Limiter Kit	cslsmiffy	Parts For Sale	12	13-02-2009 11:40 AM
NEW PRODUCT FOR E46 M3 ROUGE ENGINEERING 'X' PIPE	CA AUTOMOTIVE UK	Main Message Centre	2	21-07-2008 07:02 PM
Bush limiter kit??	jim76	Technical Area	12	05-06-2008 03:44 PM
1 x Turner Motorsport Rear Trailing Arm Bush Limiting Kit	Rezmund	Parts For Sale	6	04-01-2008 06:55 PM

28-10-2008, 06:10 PM	#2
Bravo73 S3 - On the open road Join Date: Jun 2008 Posts: 91 Casino cash: $675	If you're getting the work done at Simpsons, I suggest that you go with the Turner's version. Simpsons obviously choose to stock the Turner one for a reason. Are you getting the bushes themselves changed at the same time?

28-10-2008, 07:08 PM	#3
cslbecks S4 - Getting the hang of it Join Date: Oct 2008 Location: London, Essex Posts: 178 Casino cash: $250	I dont think my bushes will need changing - the cars only done 16k - but will get them to check them and if they need doing i will get them replaced also. I just wondered if anyone had had the Rogue Limiter kit fitted??

28-10-2008, 07:13 PM	#4
Bravo73 S3 - On the open road Join Date: Jun 2008 Posts: 91 Casino cash: $675	If you're going to the hassle and cost of having the limiting kit fitted, you'd be daft to not change the bushes at the same time. IIRC, the bushes themselves cost around £15 and the additional labour shouldn't be that much. I would even go as far to say that Simpsons will advise you to fit new bushes anyway. They certainly did when I bought the limiting kit off them recently.

28-10-2008, 07:41 PM	#5
cslbecks S4 - Getting the hang of it Join Date: Oct 2008 Location: London, Essex Posts: 178 Casino cash: $250	Yes - i wont scrimp if they need doing - but dont really see the point if they are ok?? Its not the cost of the bushes, its the extra labour - but as i said i wont scrimp if they need doing - knowing me i will most likely get them done anyway so i know everythings fresh etc. Thanks as always Bravo for your help and advice.

28-10-2008, 10:50 PM	#7
cslbecks S4 - Getting the hang of it Join Date: Oct 2008 Location: London, Essex Posts: 178 Casino cash: $250	ok - cool - will most likely get them done then regardless!

02-01-2009, 07:29 PM	#9
pkumarm3 S2 - Picking it up Join Date: Jan 2009 Location: USA Posts: 41 Casino cash: $700	Powerflex RTABs are the best you can buy they are poly-urethane. they are stiff, but also have some play so you won't be killing yourself when your car creaks non stop (like it would with the Rogue RTABs)