CSL engine - advice sought!

Matt62 · 10-01-2011, 01:06 AM

Hi! Some may know me from other forums, I race an E46 M3 V8 GTR. But I have an E46 M3 road-car. I considered the CSL but opted for an M3 spec'd up instead.

I've done the suspension, brakes etc and now have the bits I need to turn my engine into a CSL engine, I have a genuine CSL airbox, CSL ECU and wiring loom. This will be installed in a few weeks and the ECU re-mapped.

The question for you chaps is should I be looking for CSL cams as well or will a re-mapped and tweaked CSL ECU with standard M3 cams be sufficient to have similar power output ?

I suspect many of you have upgraded your CSL camshafts ? My experience, only in the race cars, is that with very high lift camshafts the bottom-end is severly sacrificed. How have people found upgraded camshafts? Should I just go for this instead perhaps ?

Any thoughts or advice would be much appreciated!

DuncanR · 10-01-2011, 09:57 AM

Sorry cant help Matt.... new engine under warranty !! Others will be along soon with their fourpennuth !!

**glendog74** · 10-01-2011, 10:11 AM

There was a rather long and tedious post about this sort of thing some time back

:

http://www.cslregister.com/forum/showthread.php?t=5199

The Gorilla · 10-01-2011, 11:20 AM

Hi,

Are your running the S62 or S65 V8 in the E46 ?

With or without Vanos ?

Std or Higher lift Cams ?

OEM or Stand alone ECU ? Pectel/Motec/ KMS-Pi ~?

Reason for the questions is that if you needed V8
''Power'' for the E46 Race Car then why are you
not following suit with your Road Car if its all
about 'Power' increase ?

A standard V8 will be much easier to live with in a
Road Car than a screaming S54 that falls off high lift
cams at anything under 6,000 rpm.

Especially as the S65 is around the same weight
as the S54 and a little bit shorter.

Further, you already have the knowledge and
know how from the Race V8.

Regards,

The Gorilla.

Matt62 · 10-01-2011, 01:05 PM

Thanks for your thoughts Gorilla.

It's a huge can of worms to stick an S62 in the E46 M3 !

To give you some idea it took us about 4 years to get it right in the race car. The engine in that car produces 570bhp and has had about £15k spent on it + £10k every season or two for an overhaul. It's had all major internal components upgraded.

Also, I'm not wanting that kind of power, even if I wanted 500bhp I would just supercharge the S54.

What I want is the CSL noise above anything else! A bit of extra power would be a benefit, but it's not the main reason. Just wondering if CSL cams would give me any benefit at all, but it's not esssential.

The Gorilla · 10-01-2011, 02:37 PM

Hi,

Matt62- I think BMW pulled off one of the
biggest Motorsport Illusions of all time with
the V8 M3 GTR ALMS 2000/1 Cars.

The point being that although the 'GTR'
shares the S62 Block, the Mader Mecachrom
in the GTR with its Flat Plane Crank special cams
and so on, let alone internals, Dry Sump etc, is at another
level to where S62/S65 M engines can only
dream and aspire to be.

The Red Bull / Renault V8 owes much to a BMW Block !!!

The Cross Plane Crank of the S62 is not user freindly
to high revs, and although it makes good torque the
S62 base engine at 245 Kg's v the 155 Kgs of the Mader V8
is only part of the story.

Still, CSL, bit more Cam on a road Going S54 is Ok,
but as you say, too agrressive and all your doing is
pushing the 'on' Cam Power band further up the
rev counter.

Not exactly what you want in a road car.

If you can find some cams within budget, then fine,
if not, then for a daily driven road car, I would
leave it as is, and just have the ECU remapped
accordingly.

Regards,

The Gorilla.

10-01-2011, 01:06 AM	#1
Matt62 Wonky 'L' after Washing Join Date: Apr 2010 Posts: 13 Casino cash: $359	CSL engine - advice sought! Hi! Some may know me from other forums, I race an E46 M3 V8 GTR. But I have an E46 M3 road-car. I considered the CSL but opted for an M3 spec'd up instead. I've done the suspension, brakes etc and now have the bits I need to turn my engine into a CSL engine, I have a genuine CSL airbox, CSL ECU and wiring loom. This will be installed in a few weeks and the ECU re-mapped. The question for you chaps is should I be looking for CSL cams as well or will a re-mapped and tweaked CSL ECU with standard M3 cams be sufficient to have similar power output ? I suspect many of you have upgraded your CSL camshafts ? My experience, only in the race cars, is that with very high lift camshafts the bottom-end is severly sacrificed. How have people found upgraded camshafts? Should I just go for this instead perhaps ? Any thoughts or advice would be much appreciated!

10-01-2011, 09:57 AM	#2
DuncanR CSL Register Uber-poster! Join Date: Sep 2009 Location: Olney, Bucks Posts: 3,735 Casino cash: $9984	Sorry cant help Matt.... new engine under warranty !! Others will be along soon with their fourpennuth !! __________________ " I use Gleaming Kleen.... for that new car look " I wish I had used - Race Data Systems - Motorsport Data Loggers forgive me Nathan !

10-01-2011, 10:11 AM	#3
glendog74 CSL Register Uber-poster! Tetris Champion! Join Date: Apr 2008 Location: Cornwall Posts: 8,861 Casino cash: $32299	There was a rather long and tedious post about this sort of thing some time back : http://www.cslregister.com/forum/showthread.php?t=5199 __________________ Cha'mone Mother F**ker!

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-01-2011, 11:20 AM	#4
The Gorilla S5, Sport Off, DSC M-track Join Date: Apr 2008 Posts: 740 Casino cash: $14401	Hi, Are your running the S62 or S65 V8 in the E46 ? With or without Vanos ? Std or Higher lift Cams ? OEM or Stand alone ECU ? Pectel/Motec/ KMS-Pi ~? Reason for the questions is that if you needed V8 ''Power'' for the E46 Race Car then why are you not following suit with your Road Car if its all about 'Power' increase ? A standard V8 will be much easier to live with in a Road Car than a screaming S54 that falls off high lift cams at anything under 6,000 rpm. Especially as the S65 is around the same weight as the S54 and a little bit shorter. Further, you already have the knowledge and know how from the Race V8. Regards, The Gorilla.

10-01-2011, 01:05 PM	#5
Matt62 Wonky 'L' after Washing Join Date: Apr 2010 Posts: 13 Casino cash: $359	Thanks for your thoughts Gorilla. It's a huge can of worms to stick an S62 in the E46 M3 ! To give you some idea it took us about 4 years to get it right in the race car. The engine in that car produces 570bhp and has had about £15k spent on it + £10k every season or two for an overhaul. It's had all major internal components upgraded. Also, I'm not wanting that kind of power, even if I wanted 500bhp I would just supercharge the S54. What I want is the CSL noise above anything else! A bit of extra power would be a benefit, but it's not the main reason. Just wondering if CSL cams would give me any benefit at all, but it's not esssential.

10-01-2011, 02:37 PM	#6
The Gorilla S5, Sport Off, DSC M-track Join Date: Apr 2008 Posts: 740 Casino cash: $14401	Hi, Matt62- I think BMW pulled off one of the biggest Motorsport Illusions of all time with the V8 M3 GTR ALMS 2000/1 Cars. The point being that although the 'GTR' shares the S62 Block, the Mader Mecachrom in the GTR with its Flat Plane Crank special cams and so on, let alone internals, Dry Sump etc, is at another level to where S62/S65 M engines can only dream and aspire to be. The Red Bull / Renault V8 owes much to a BMW Block !!! The Cross Plane Crank of the S62 is not user freindly to high revs, and although it makes good torque the S62 base engine at 245 Kg's v the 155 Kgs of the Mader V8 is only part of the story. Still, CSL, bit more Cam on a road Going S54 is Ok, but as you say, too agrressive and all your doing is pushing the 'on' Cam Power band further up the rev counter. Not exactly what you want in a road car. If you can find some cams within budget, then fine, if not, then for a daily driven road car, I would leave it as is, and just have the ECU remapped accordingly. Regards, The Gorilla.