RTAB tool

**Fasteddie** · 17-03-2010, 05:54 PM

Hi does anybody have the tool required for the RTAB removal, this job doesn't look that bad and I'd like to do it but wondered if anybody localish has a tool they can lend me or otherwise does anybody know where I can rent one - if that is possible.

1cosmicboy · 17-03-2010, 06:21 PM

if ur careful ,they can be easily drilled out.or use a couple of good quality sockets and a vice .hope this helps

**Fasteddie** · 17-03-2010, 09:50 PM

site seems slow tonight?
Thanks cosmicboy, are you using a vice in situ? Thinking about I may have a go with a few G clamps. Can somebody give me an idea of what's best. Ploy bushes or std bushes with limiter or poly bush and limiter?

**shimmy** · 17-03-2010, 09:59 PM

dont think poly bushes need a limiter

my philosophy is that poly bushes will shake the car to bits withiout as cage - so stick to rubber

**Fasteddie** · 17-03-2010, 10:28 PM

so std rubber bush and a limiter then? I expect if I'm going to go as far as fit the limiters then the bush should be replaced?? oem or is there a better bush without going poly?

NZ_M3 · 17-03-2010, 11:47 PM

To be honest I'd just buy the tool rather than muck around with a drill.

I did mine with a tool and it makes life a whole lot easier having one and much faster too. You'll also be less likely to damage stuff.

Got mine from here: I also have the FCAB one too, but have not used that myself.

http://www.mistools.net/

Standard bushing + limiter is a great setup (I use the Vorshlag limiter kit and find it to be pretty good)

17-03-2010, 05:54 PM	#1
Fasteddie S4 - Getting the hang of it Join Date: Feb 2010 Location: Ashford, Kent Posts: 202 Casino cash: $1434	RTAB tool Hi does anybody have the tool required for the RTAB removal, this job doesn't look that bad and I'd like to do it but wondered if anybody localish has a tool they can lend me or otherwise does anybody know where I can rent one - if that is possible.

17-03-2010, 06:21 PM	#2
1cosmicboy S5 - Full Throttle Join Date: Jan 2009 Location: northumberland Posts: 289 Casino cash: $1196	if ur careful ,they can be easily drilled out.or use a couple of good quality sockets and a vice .hope this helps __________________ forcat,s de la route !

17-03-2010, 09:59 PM	#4
shimmy CSL Register Uber-poster! Join Date: Apr 2008 Location: Uk Posts: 14,646 Casino cash: $43909	dont think poly bushes need a limiter my philosophy is that poly bushes will shake the car to bits withiout as cage - so stick to rubber __________________ .

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

17-03-2010, 09:50 PM	#3
Fasteddie S4 - Getting the hang of it Join Date: Feb 2010 Location: Ashford, Kent Posts: 202 Casino cash: $1434	site seems slow tonight? Thanks cosmicboy, are you using a vice in situ? Thinking about I may have a go with a few G clamps. Can somebody give me an idea of what's best. Ploy bushes or std bushes with limiter or poly bush and limiter?

17-03-2010, 10:28 PM	#5
Fasteddie S4 - Getting the hang of it Join Date: Feb 2010 Location: Ashford, Kent Posts: 202 Casino cash: $1434	so std rubber bush and a limiter then? I expect if I'm going to go as far as fit the limiters then the bush should be replaced?? oem or is there a better bush without going poly?

17-03-2010, 11:47 PM	#6
NZ_M3 S5, Sport On, DSC M-track Join Date: Jun 2008 Location: Auckland, New Zealand Posts: 1,434 Casino cash: $13579	To be honest I'd just buy the tool rather than muck around with a drill. I did mine with a tool and it makes life a whole lot easier having one and much faster too. You'll also be less likely to damage stuff. Got mine from here: I also have the FCAB one too, but have not used that myself. http://www.mistools.net/ Standard bushing + limiter is a great setup (I use the Vorshlag limiter kit and find it to be pretty good)